Home / Guides / Sound masking / Cubicle privacy
For open plans and cubicle floors
Cubicle privacy that actually works
A cubicle gives visual privacy immediately and acoustic privacy almost never. The panels are usually too low to interrupt the path a voice takes, the ceiling above reflects whatever clears them, and the background in a quiet office is too low to hide anything. All three are fixable, and only one of them costs much.
Know what height is worth paying for
A panel that does not break the line of sight between two seated heads does very little acoustically. The threshold is higher than most furniture is.
Fix the ceiling, not just the panel
Sound that clears a panel reflects off the ceiling and lands two desks away. An absorbent ceiling is often the better purchase.
Cover what is left
Panels and ceilings reduce what arrives. Masking makes what still arrives unintelligible, and on an open floor it is usually the cheapest of the three.
How to check your floor
- Sit down and look over your panel. If you can see the face of the person opposite, sound has a clear path too.
- Measure the panel height. Much below 1.6 m from the floor and it does very little between two seated people.
- Clap once, hard. A bright ringing tail means the ceiling is bouncing sound over the panels and landing it two desks away, and an absorbent ceiling matters more than taller panels.
- Then get masking quoted for the floor. That is the part that makes the speech which still arrives unintelligible.
Height is the whole point of a panel
A barrier works by interrupting the direct path between a talker and a listener. Seated head height is around 48 inches, so a 42-inch panel interrupts nothing between two seated people and only looks like it does. Meaningful blocking starts once the panel is clearly above seated head height, which in practice means around 60 to 65 inches or more.
That is a real trade against light, sight lines, and how the floor feels, which is why so many offices chose low panels and then discovered the noise. Where tall panels are not acceptable, the honest answer is that blocking has been given up and the other three tools have to do the work.
The absorbent face should point at the talker
A panel that is hard on both faces reflects sound back into the space it came from, which helps the listener a little and the talker not at all. A panel with an absorbent surface takes energy out of the system rather than redirecting it.
Where only one face can be absorbent, it should face the person making the noise. In a back-to-back layout that means the inside of each workstation.
The ceiling decides what happens next
Anything that clears the panel goes up, hits the ceiling, and comes down somewhere else on the floor. With a hard or reflective ceiling that path is often stronger than the one through the panel, and it is why open plans can carry a voice a surprising distance.
A suspended acoustic tile with a high absorption rating is the single most effective change available on most cubicle floors, because it is a very large surface and nobody competes for it. It is frequently cheaper than replacing furniture.
Masking is what makes the rest worth it
With panels and a ceiling doing their work, voices arrive quieter but still intelligible, because an open office floor is usually quiet enough for a distant voice to stand out clearly. Masking lifts the background by a few decibels in the speech band and the remaining intelligibility falls away.
For a whole floor that is an installed system. For one row of desks, or while a budget is being argued over, a device and a speaker placed high between the problem desks does a genuine amount of good.
What you need
- A small speaker, placed as high as the furniture allows
- A device to run the mix from, plugged in
- An absorbent panel face pointing at whoever talks most
- Headphones, as the fallback for one person on a loud floor
Mistakes to avoid
- Buying 42-inch panels and expecting acoustic privacy
- Hard panel faces on both sides
- Leaving a reflective ceiling untouched
- One loud speaker for the whole floor instead of several quiet ones
Questions
How tall do cubicle panels need to be for privacy?
High enough to break the line of sight between two seated people, which means well above the roughly 48-inch seated head height. Around 60 to 65 inches is where blocking starts to matter.
Do cubicle walls actually block sound?
Only if they are tall enough and absorbent on the face pointing at the talker. Low, hard panels give visual privacy and very little acoustic privacy.
How do you get privacy in an open office?
Absorb with an acoustic ceiling, block with tall enough screens, cover the remainder with masking, and separate people who need quiet from people who talk all day.
Can I use white noise for cubicle privacy?
Masking shaped to the speech band works better at a lower, more comfortable level than plain white noise. Place the speaker high, between the desks that overhear each other.
Get it quoted
Tell us about the space and we will pass it to as many installers in your area as we can, so you get real quotes to compare. They survey it, fit the system, and tune it. Free, and nothing to pay at any point.
