SoundMasker

Home / Guides / Sound masking / Sound masking systems

For facility managers and architects

Sound masking systems, explained

An installed sound masking system is a network of small loudspeakers above the ceiling, a controller that generates a shaped noise signal, and a day of tuning that matters more than the hardware. This page explains what the parts do, what they cost, and the questions that separate a complete quote from a cheap one.

1

Know what you are buying

Speakers, a controller, the zoning, and a day of tuning. Knowing which part does what is how you tell a complete quote from a cheap one.

2

Know the numbers first

Installed systems run $1.50 to $3.00 per square foot. Knowing that, and knowing what commissioning should cost, means a quote can be read rather than trusted.

3

Quotes you can compare

Describe the space once and we pass it to as many installers in your area as we can, so the numbers that come back mean something next to each other.

How to approach it

  1. Measure or estimate the square footage of the area to be covered, and note the ceiling type. Those two decide most of the price.
  2. Work out roughly how the space divides: open floor, private offices, corridors, meeting rooms. Each becomes a zone with its own level.
  3. Get quotes from more than one installer, each working from the same description, so the prices are comparable.
  4. Check that commissioning is its own line in every quote, with a meter and a written record of the level in each zone.
  5. In an occupied office, ask for the level to be raised gradually over a few weeks rather than switched on at full on the first morning.
Where to put the speaker: sound masking systems

What the parts are

A controller or network panel generates the masking signal and feeds it to loudspeakers, usually called emitters. Speakers are placed on a grid, commonly about one every 100 square feet at a normal ceiling height, and the controller shapes the sound and sets the level for each zone.

There are two ways to point the speakers. An indirect or plenum system aims them upward into the space above the ceiling, so the sound reflects and diffuses before it reaches people. A direct-field system aims them at the occupied space, which gives a more even and more controllable field and is what most new installations use. Open ceilings and exposed decks need surface or pendant mounts instead, and cost more to install.

What the parts are

Zoning is most of the design

A corridor, a waiting area, a row of private offices, and an open floor all want different levels. Each one becomes a zone with its own control. Tuning a single zone to serve a conference room and the open plan next to it produces a compromise that works in neither.

This is why two buildings of the same size can be quoted at opposite ends of the range. Fifteen private offices with their own volume controls is a different job from one open floor of the same square footage.

Commissioning is the part that gets cut

Commissioning means walking the finished space with a sound level meter, verifying the level at several points in every zone, adjusting each speaker in small steps, and confirming the spectrum matches the room. It usually costs $1,500 to $4,000 and it is the most commonly removed line in a competitive bid.

A system left at factory defaults is the usual reason people say masking sounds like a hiss. The hardware was never the problem.

What it costs

New construction runs about $1.50 to $2.50 per square foot, roughly half equipment and half labour. A retrofit in an occupied space runs $2.00 to $3.00, because crews work around furniture and staff. Exposed or unusually high ceilings add twenty to forty per cent to labour. A full facility with volume controls in each private office runs $2.00 to $4.00 all in.

In practice: a 5,000 square foot new build lands around $7,500 to $12,500, and a 10,000 square foot retrofit around $20,000 to $30,000. Larger projects pay less per square foot. Add commissioning, and an acoustic assessment at $1,000 to $5,000 if the space has problems worth measuring first.

What a browser tab can and cannot do

It can produce the right signal, let you hear the difference, and cover a small room well enough to matter. For one private office, a therapy room, or a front desk, a device and a decent speaker is a real solution and costs nothing.

It cannot give you an even field across a floor. It cannot zone, it cannot be tuned to a uniform level from one end of a space to the other, it needs a device and a speaker in every room, and nobody will commission it with a meter. Past a few rooms, those limits are the whole reason installed systems exist.

What you need

  • A laptop, tablet, or old phone for the trial
  • A small wired speaker, placed high if possible
  • A free sound level meter app, to see roughly where you are
  • A floor plan, if you are going to ask anyone for a quote

Mistakes to avoid

  • Buying before hearing the signal in your own space
  • Letting commissioning be removed from a bid to win it on price
  • Masking a reverberant room before adding any absorption
  • Switching a new system on at full level on the first morning

Questions

How much does a sound masking system cost?

About $1.50 to $2.50 per square foot for new construction and $2.00 to $3.00 for a retrofit in an occupied space, plus $1,500 to $4,000 for commissioning. A 10,000 square foot retrofit is usually $20,000 to $30,000.

How loud should a sound masking system be?

Usually 40 to 48 dBA, set higher in open areas and lower in private offices and corridors. Above about 48 dBA people start to notice it as noise.

Plenum or direct-field?

Direct-field is the more common choice now because the field is more even and easier to tune. Plenum systems rely on the space above the ceiling to diffuse the sound, which varies from building to building.

Can I just use a few white noise machines instead?

For one or two rooms, yes, and so can a browser tab. For a floor, no: you cannot get an even level or separate zones out of a handful of machines, and uneven masking is more irritating than none.

How long does an installation take?

A small single-zone job is a day. A floor is usually a few days, plus a separate commissioning visit. Best practice in an occupied office is to raise the level gradually over two to four weeks so people habituate.

Get it quoted

Tell us about the space and we will pass it to as many installers in your area as we can, so you get real quotes to compare. They survey it, fit the system, and tune it. Free, and nothing to pay at any point.

Related