Home / Guides / Sound masking / Conference rooms
For rooms where confidential things get said
Conference room soundproofing
A meeting room is where the confidential conversations happen and it is usually the least private room on the floor: glass on one side, a hollow door, and a partition that stops at the ceiling grid. The three failures are predictable and they have a sensible order. This page covers that order, and what masking does in the corridor outside.
Fix the leak before the wall
Almost every leaky meeting room has an open plenum above it or a gap under the door. Both cost very little next to construction.
Protect the outside, not just the inside
Masking in the corridor and the open plan outside the room is often what finally stops conversations carrying, and it is the cheapest element.
Glass is not the problem people assume
A sealed glass wall outperforms a plasterboard one that stops at the ceiling grid. The junctions matter more than the material.
How to find the leak
- Have a colleague talk normally inside the room with the door closed, and listen from outside.
- Lift a ceiling tile outside the room and check whether the partition continues above it. If not, that is the leak.
- Check the door: a hollow slab with a gap underneath undoes most of a good wall.
- Ask for masking to be quoted for the corridor and the nearest open area, not for inside the meeting room.
The three usual failures
The plenum. Partitions that stop at the suspended ceiling leave a shared space above several rooms, and sound travels over the wall as if it were not there. A plenum barrier above the wall line, or continuing the partition to the deck, is the fix, and it matters more than anything done to the wall face.
The door. A hollow-core slab with an undercut is a large opening with a thin cover. A solid-core door with perimeter seals and a drop seal at the threshold is one of the best-value improvements available in any office.
The glass. Single glazing in a thin frame blocks less than people assume, and an unsealed frame blocks much less again. Thicker laminated glass, or double glazing with an air gap and good seals, performs far better. Where the glass is a given, treat it as a known weakness and compensate outside the room.
Treating the inside and the outside differently
Inside the room, the problem is usually comfort and call quality: a glass box with a hard table rings, which makes conference calls tiring and speech harder to follow. That is absorption, and a ceiling plus one or two wall panels normally settles it.
Outside the room, the problem is privacy, and absorption does not help it. Masking in the corridor and in the open plan beyond the door is what makes a conversation that still gets through unintelligible. Protecting a meeting room is largely a matter of treating the space around it.
Sequence and cost
In order of value for money: seal the door, barrier the plenum, add masking outside, absorb inside, and only then consider the glass or the wall assembly.
The first three are typically a few hundred to a few thousand dollars for one room. Replacing glazing or rebuilding a partition is a construction project, and in a leased space it is often not available at all. Doing the cheap three first frequently removes the need to find out.
What you need
- Perimeter seals and a drop seal for the door
- A plenum barrier above the wall line, if the wall stops at the grid
- A small speaker outside the room, for masking
- A couple of absorbent panels inside, for call quality
Mistakes to avoid
- Treating the wall face while the plenum above it stays open
- Leaving a hollow door with a gap underneath
- Putting the masking speaker inside the meeting room
- Assuming a glass partition blocks as much as it looks like it should
Questions
How do you soundproof a conference room?
Seal the door with perimeter and drop seals, close the gap above the ceiling with a plenum barrier or a full-height wall, add masking in the space outside the room, and add absorption inside for call quality.
Why can people hear through our glass meeting room?
Single glazing in a thin, unsealed frame blocks much less than it appears to, and the partition above the ceiling is often open as well. Treat the frame seals and the plenum first.
Should sound masking go inside or outside a meeting room?
Outside. The point is to make speech leaving the room unintelligible to people in the corridor and the open plan. Masking inside the room only makes the meeting harder to hear.
What does conference room soundproofing cost?
Door seals, a plenum barrier, and masking outside are usually a few hundred to a few thousand dollars per room. Replacing glazing or rebuilding the partition is construction and costs considerably more.
Get it quoted
Tell us about the space and we will pass it to as many installers in your area as we can, so you get real quotes to compare. They survey it, fit the system, and tune it. Free, and nothing to pay at any point.
